500W CMY Beam Spot LED Moving Head Party Lighting Spot Projection LED Moving Head Sharpy Beam Stage Light Moving Head Stage Light
Input voltage :AC90V-240V/50-60HZ
Light source specification: ECO500-80-R00-000
Life of light source: 20000 hours
Lumen illumination: 4 m 120000 lm
Outlet aperture: 138MM
Rated power :600W
Channel mode :22/27 channels
Horizontal scanning :540 degrees (16bit precision scanning) electronic error correction
Vertical scanning :270 degree (16bit precision scanning) electronic error correction
Dimming system :0-100% linear adjustment
Focusing system: Linear adjustment of 4 m to 50 m
Atomizing system :1 independent atomizing effect, light spot soft and natural
Zoom Angle: Beam 2.7 ~ 40° Staining 4-40° Pattern 4-40°
High speed stroboscopic: 0-30 times/second. Adjustable
speed stroboscopic effect. Strobe macro function
Color: 8 colors + white light. Color half color function
Color system: Independent CMY+CTO color mixing system.
Fixed pattern: 12 fixed pattern + white light
Rotation pattern :7 glass patterns, each glass pattern can be independent positive and negative rotation
Prism system: Standard single 6 row prism and 8 prism, each prism can be independent positive and negative rotation
Macro power: console reset function, self - walk mode, master - slave mode
Display mode: LCD display, button + touch dual operation
mode
Control signal: International standard DMX512. With RDM
function, online software upgrade, dial address code
Cooling mode: Use axial fan to strengthen cooling
Safety device: with electronic temperature control
overheating protection, overheating system failure
electronic temperature control automatic power protection
Appearance material: high temperature resistant plastic
Working environment :-20 degrees, 40 degrees
Cable connection(DMX)
Use a cable conforming to specifications EIA RS-485: 2-pole twisted, shielded, 120Ohm characteristic impedance, 22-24 AWG, low capacity.
Do not use microphone cable or other cable with characteristics differing from those specified. Theendconnections must be made using XLRtype3 or 5-pin male/female connectors.
A terminating plug must be inserted into the last projector with a resistance of 120Ohm (minimum 1/4W)between terminals 2 and3.
IMPORTANT: The wires must not make contact with each other or with the metal casing of the connectors. The casing itself must be connected to the shield braid and to pin 1 of the connectors.
Operation Instructions
-The moving head is for beam wash spot purpose.
-Don't turn on the fixture if it's been through severe temperature difference like after transportation because it might damage the light due to the environment changes. So make sure to operate the fixture until it is in normal temperature.
-This light should be keep away from strong shaking during any transportation or movement.
-Don't pull up the light by only the head, or it might cause damages to the mechanical parts.
-Don't expose the fixture in overheat, moisture or environment with too much dust when installing it. And don't lay any power cables on the floor. Or it might cause electronic shock to the people.
-Make sure the installation place is in good safety condition before installing the fixture.
Sub Menu(Parameter)
DMX channel sheet
| Channel |
Function |
| 1 |
Pan move |
| 2 |
Pan fine-tuning |
| 3 |
Tilt move |
| 4 |
Tilt fine-tuning |
| 5 |
XY speed |
| 6 |
Dimmer |
| 7 |
Strobe |
| 8 |
Color wheel |
| 9 |
Zoom motor |
| 10 |
Reset |
If you use a controller with a 5 pin DMX output connector. You will need to use a 5pin to 3 pin as apter
Model No: DMX5M. Or DMX 5F
The chart below details a proper cable conversion:
At first link the first light and DMX control through XLR-connection signal cable, then connect the light in series, as the follow:
Parameter value setting
When the selected item is value need to been modified, the dialog shown in Figure 4 will popup.
Installation Instructions
Light fixtures can be placed horizontally, slanted, and hung upside down.Be sure to pay attention to the installation method when hanging diagonally and upside down.
As shown in Figure 2, before positioning the lamp, it is necessary to ensure the stability of the installation site. When installing the reverse hanging, it is necessary to ensure that the lamp does not fall down on the support frame. It is necessary to use the safety rope through the support frame and the lamp handle for auxiliary hanging to ensure safety. Prevent the luminaire from falling and sliding.
When installing and debugging the lamps, it is forbidden for pedestrians to pass under them. Regularly check whether the safety rope is worn and whether the hook screws are loose.
Our company does not assume any responsibility for all consequences caused by the fall of the lamp due to the unstable installation of the hanging.
Schematic diagram of the lamp hanging upside down
Packing list
Sea transportation / Air transportation / Rail transportation / International express
LED stage lights have a wide range of applications in the entertainment industry. Here are some key areas where LED stage lights are commonly used:
Concerts and Live Music Performances: LED stage lights create dynamic lighting effects that enhance the atmosphere and visual impact of live music events.
Theater Productions: LED stage lights are utilized to set the mood, highlight actors or scenes, and create captivating lighting designs that complement the storytelling.
Dance Performances: LED stage lights are employed to accentuate dance movements, create vibrant color palettes, and add visual excitement to dance performances.
Corporate Events and Conferences: LED stage lights are used to provide professional lighting setups for keynote speeches, presentations, and product launches, enhancing the overall visual experience.
Fashion Shows: LED stage lights are utilized to create dramatic and evocative lighting designs that enhance the runway and showcase the clothing creations.
Television and Film Productions: LED stage lights are incorporated into studio setups to provide versatile and controllable lighting solutions for TV shows, movies, and commercials.
Theme Parks and Attractions: LED stage lights are used to illuminate rides, shows, and themed areas in theme parks, providing immersive lighting experiences for visitors.
Nightclubs and DJ Performances: LED stage lights are employed to create vibrant, energetic lighting displays that synchronize with the music and enhance the clubbing experience.
Exhibitions and Trade Shows: LED stage lights are utilized to highlight products, create visually appealing displays, and draw attention to exhibition booths.
Architectural Lighting Installations: LED stage lights are used to illuminate iconic buildings, monuments, and landmarks, enhancing their visual appeal and creating stunning nighttime displays.
These applications demonstrate the versatility and impact of LED stage lights in various entertainment, commercial, and architectural settings, ensuring captivating visual ex
){kind=link}