250W DMX512 3-IN-1 Sharp DJ Moving Head Lamp Party Light Concert Laser Light LED Moving Head Sharpy Beam Stage Light Moving Head Stage Light
Light source power: 250W
Voltage: AC 200V~240V/50~60Hz;
Color disk: Each color disk consists of 9 color plates + white light;
Pattern plate: 9 gobos+white effects;
Glass pattern: 7 gobos+white effects;
540° translation, 270° tilt.
Overheat protection;
Control mode: DMX512/ master-slave/Automatic;
IP20 protection level
Signal cable connection
Light fixtures feature standard DMX input and output 3-core or 5-core XLR sockets.Use a
shielded twisted-pair signal cable designed for DMX 512;The signal line is generally
connected at 150 meters, and the DMX512 signal amplifier must be added for long distance signal transmission.
Connect a shielded twisted-pair signal line from the DMX outlet of the controller to the DMX input of the first device, and from the DMX outlet of the first device to the DMX input of the second device, and so on, until all lights have been connected. Then install a terminal plug on the last connected light outlet 3-core jack on each circuit.(Weld a 4/1W, 120Ω resistor between the 2 and 3 pins of the 3-core pin cannon plug).
| Options |
Instructions |
| Running mode |
DMX |
Slave state: Receives DMX signals from the console or mainframe |
| |
Bootstrapping |
Host state: Self-actuated and sends DMX signal to slave |
| |
Voice control |
|
| DMX address |
1-512 |
Press "OK" to enter editing mode.At this point, the hundreds digit is selected, and press the "up" and "down" keys to change the address code.Press the "OK" key again to select the tens edit.Press "OK" once more to select the ones edit.Press again to exit the editing state |
| Motor reset |
Off |
|
| |
On |
Light fixture reset |
| Channel mode |
24CH |
24 channel mode |
| Language |
Chinese |
Set to the Chinese interface |
| |
English |
Set to the English interface |
| Screen flip |
Off |
Front display |
| |
On |
Screen reverse display |
| X Inversion |
Off |
|
| |
On |
|
| Y-reverse |
Off |
|
| |
On |
|
| XY swap |
Off |
|
| |
On |
Channel for switching XY axes (including trims) |
| XY encoder |
On |
Use an encoder (optocoupler) to judge out of step and automatically correct the position |
| |
Off |
Correct the position without using an encoder (optocoupler) |
DMX signal
|
Hold |
Continue running in its original state |
| |
Clear zero |
Turn the motor back and stop running |
| The color wheel changes linearly |
On |
The color wheel changes linearly |
| |
Off |
Color wheel nonlinear change, half color change |
| Restore default Settings |
|
When you see the confirmation dialog after pressing "OK", press "OK" again to restore the default Settings |
| Channel |
Function |
| 1 |
Color |
| 2 |
Strobe |
| 3 |
Dimming |
| 4 |
Gobo |
| 5 |
Prism 1 |
| 6 |
Prism 2 |
| 7 |
Prism 1 Rotate |
| 8 |
Prism 2 Rotate |
| 9 |
Frost & Colorful |
| 10 |
Focus |
| 11 |
X |
| 12 |
X Fine |
| 13 |
Y |
| 14 |
Y Fine |
| 15 |
XY Speed |
| 16 |
Reset |
| 17 |
LED_Dimming |
| 18 |
LED_Strobe |
| 19 |
LED_Red |
| 20 |
LED_Green |
| 21 |
LED_Blue |
| 22 |
LED_Color macro |
| 23 |
LED_Scene |
| 24 |
LED_Scene Speed |
If you use a controller with a 5 pin DMX output connector. You will need to use a 5pin to 3 pin as apter
Model No: DMX5M. Or DMX 5F
The chart below details a proper cable conversion:
At first link the first light and DMX control through XLR-connection signal cable, then connect the light in series, as the follow:
Control panel
Installation Instructions
Light fixtures can be placed horizontally, slanted, and hung upside down.Be sure to pay attention to the installation method when hanging diagonally and upside down.
As shown in Figure 2, before positioning the lamp, it is necessary to ensure the stability of the installation site. When installing the reverse hanging, it is necessary to ensure that the lamp does not fall down on the support frame. It is necessary to use the safety rope through the support frame and the lamp handle for auxiliary hanging to ensure safety. Prevent the luminaire from falling and sliding.
When installing and debugging the lamps, it is forbidden for pedestrians to pass under them. Regularly check whether the safety rope is worn and whether the hook screws are loose.
Our company does not assume any responsibility for all consequences caused by the fall of the lamp due to the unstable installation of the hanging.
Schematic diagram of the lamp hanging upside down
Packing list
Sea transportation / Air transportation / Rail transportation / International express
LED stage lights have a wide range of applications in the entertainment industry. Here are some key areas where LED stage lights are commonly used:
Concerts and Live Music Performances: LED stage lights create dynamic lighting effects that enhance the atmosphere and visual impact of live music events.
Theater Productions: LED stage lights are utilized to set the mood, highlight actors or scenes, and create captivating lighting designs that complement the storytelling.
Dance Performances: LED stage lights are employed to accentuate dance movements, create vibrant color palettes, and add visual excitement to dance performances.
Corporate Events and Conferences: LED stage lights are used to provide professional lighting setups for keynote speeches, presentations, and product launches, enhancing the overall visual experience.
Fashion Shows: LED stage lights are utilized to create dramatic and evocative lighting designs that enhance the runway and showcase the clothing creations.
Television and Film Productions: LED stage lights are incorporated into studio setups to provide versatile and controllable lighting solutions for TV shows, movies, and commercials.
Theme Parks and Attractions: LED stage lights are used to illuminate rides, shows, and themed areas in theme parks, providing immersive lighting experiences for visitors.
Nightclubs and DJ Performances: LED stage lights are employed to create vibrant, energetic lighting displays that synchronize with the music and enhance the clubbing experience.
Exhibitions and Trade Shows: LED stage lights are utilized to highlight products, create visually appealing displays, and draw attention to exhibition booths.
Architectural Lighting Installations: LED stage lights are used to illuminate iconic buildings, monuments, and landmarks, enhancing their visual appeal and creating stunning nighttime displays.
These applications demonstrate the versatility and impact of LED stage lights in various entertainment, commercial, and architectural settings, ensuring captivating visual ex
){kind=link}